| Items |
 BLEM23-A / BLED3AM-R 30 W (1/25 HP) BLE Series Brushless DC Motor Speed Control System (Single-Phase 100-120 VAC) Web Price $516.00
|
 BLEM23-GFS / GFS2G5 / BLED3AM-R 30 W (1/25 HP) BLE Series Brushless DC Motor Speed Control System (Parallel Shaft Gearhead 5:1) (Single-Phase 100-120 VAC) Web Price $655.00
|
BLEM23-GFS / GFS2G10 / BLED3AM-R 30 W (1/25 HP) BLE Series Brushless DC Motor Speed Control System (Parallel Shaft Gearhead 10:1) (Single-Phase 100-120 VAC) Web Price $655.00
|
BLEM23-GFS / GFS2G15 / BLED3AM-R 30 W (1/25 HP) BLE Series Brushless DC Motor Speed Control System (Parallel Shaft Gearhead 15:1) (Single-Phase 100-120 VAC) Web Price $655.00
|
BLEM23-GFS / GFS2G20 / BLED3AM-R 30 W (1/25 HP) BLE Series Brushless DC Motor Speed Control System (Parallel Shaft Gearhead 20:1) (Single-Phase 100-120 VAC) Web Price $655.00
|
|||||
| Motor Frame Size | 2.36 in.60 mm | |||||||||
| Output Power | 30 W (1/25 HP) | |||||||||
| Power Supply | Single-Phase 100-120 VAC | |||||||||
| Rated Input Current | 1.3 A | |||||||||
| Shaft/Gear Type | Round Shaft (No Gearhead) | Parallel Shaft Gearhead | Parallel Shaft Gearhead | Parallel Shaft Gearhead | Parallel Shaft Gearhead | |||||
| Gear Ratio (X:1) | 5 :1 | 10 :1 | 15 :1 | 20 :1 | ||||||
| Output Shaft Diameter | 8 mm | 10 mm | 10 mm | 10 mm | 10 mm | |||||
| Rated Torque | 0.88 lb-in0.10 N·m | 3.90 lb-in0.45 N·m | 7.9 lb-in0.9 N·m | 12.3 lb-in1.4 N·m | 15.9 lb-in1.8 N·m | |||||
| Electromagnetic Brake | Not Equipped | |||||||||
| Brake Type | ||||||||||
| Static Friction Torque | ||||||||||
| Control Module Included | No | |||||||||
| Variable Speed Range (r/min) | 100 ~ 4000 | 20 ~ 800 | 10 ~ 400 | 6.7 ~ 267 | 5 ~ 200 | |||||
| Rotor Inertia | 0.48 oz-in2 | |||||||||
| Permissible Overhung Load | 0.39 in. from Shaft End = 18 lb0.79 in. from Shaft End = 22 lb10 mm from Shaft End = 80 N20 mm from Shaft End = 100 N | 0.39 in. from Shaft End = 22 lb0.79 in. from Shaft End = 33 lb10 mm from Shaft End = 100 N20 mm from Shaft End = 150 N | 0.39 in. from Shaft End = 33 lb0.79 in. from Shaft End = 45 lb10 mm from Shaft End = 150 N20 mm from Shaft End = 200 N | 0.39 in. from Shaft End = 33 lb0.79 in. from Shaft End = 45 lb10 mm from Shaft End = 150 N20 mm from Shaft End = 200 N | 0.39 in. from Shaft End = 33 lb0.79 in. from Shaft End = 45 lb10 mm from Shaft End = 150 N20 mm from Shaft End = 200 N | |||||
| Permissible Thrust Load | 9 lb40 N | 9 lb40 N | 9 lb40 N | 9 lb40 N | ||||||
| Permissible Thrust Load | The permissible thrust load should not be greater than half the motor mass. | |||||||||
| Speed Control Method (Select one of the following) | Internal potentiometer External DC voltage External potentiometer (20kΩ, 1/4W) | |||||||||
| Number of Speed Settings | 2 | |||||||||
| Multi-Speed Setting Method | 1 speed set by the internal speed potentiometer and 1 speed set by the external speed potentiometer (20 kΩ, 1/4 W) or external DC voltage (0 ~ 5 VDC or 0 ~ 10 VDC). Default is 0 ~ 5 VDC. | |||||||||
| Instantaneous Stop | Yes | |||||||||
| Multi-Axes Control | Yes | |||||||||
| Alarm Output | Yes | |||||||||
| Position Control Mode | No | |||||||||
| Torque Limit Control | No | |||||||||
| Vertical Drive (Gravitational Operation) | No | |||||||||
| Max. Extension Length (m) | 20.40 | |||||||||
| RoHS Compliant | Yes | |||||||||
| Safety Standards | CE | |||||||||
| Protocol | Modbus Protocol (Modbus RTU mode) | |||||||||
| Electrical Characteristics |
EIA-485 based Use twisted-pair wire (TIA/EIA-568B CAT5e or greater recommended), and set a max. total length of 50 m (164 ft.) |
|||||||||
| Transmission/Reception Mode | Half-duplex communication | |||||||||
| Baud Rate | 9600 bps/19200 bps/57600 bps/115200 bps | |||||||||
| Physical Layer | Start-stop synchronization mode (Data: 8-bits, stop bit: 1-bit/2-bit, parity: none/even numbers/odd numbers) | |||||||||
| Connection Type | Up to 31 units can be connected to one programmable controller (master equipment). | |||||||||
|
|
||||||||||
