| Lead Time1 | N/A {Contact your local sales office for more information.} |
Motor Type |
N/A Brushless DC Motor |
Motor Frame Size |
N/A 1.65 in.42 mm |
Output Power |
N/A 15 W (1/50 HP) |
Power Supply |
N/A 24 VDC |
Driver Type |
N/A Analog |
Type |
N/A Lead Wire |
Shaft/Gear Type |
N/A Parallel Shaft Gearhead |
Gear Ratio (X:1) |
N/A 10 :1 |
Output Shaft Diameter |
N/A 6 mm |
Degree of Protection (Motor) |
N/A IP40 |
Rated Torque |
N/A 3.8 lb-in0.43 N·m |
Variable Speed Range (r/min) |
N/A 10 ~ 300 |
Permissible Load Inertia |
N/A 77 oz-in²*When instantaneous stop or instantaneous bi-directional operation is performed = 9.3 oz-in²14 x 10-4 kg·m²*When instantaneous stop or instantaneous bi-directional operation is performed = 1.7 x 10-4 kg·m² |
Permissible Overhung Load |
N/A 0.39 in. from Shaft End = 11.2 lb10 mm from Shaft End = 50 N |
Permissible Thrust Load |
N/A 6.7 lb30 N |
Power Input |
N/A DC |
Position Control Mode |
N/A No |
Torque Limit Control |
N/A No |
Vertical Drive (Gravitational Operation) |
N/A No |
Max. Extension Length (m) |
N/A 5 |
Components |
N/A
BLH2D15-K, Brushless DC Motor Analog Driver (24 VDC) ($134.00) BLHM015K-10, 15 W (1/50 HP) Brushless DC Motor Parallel Shaft Gearhead (10:1 Gear Ratio) ($288.00) |
RoHS Compliant |
N/A Yes |
Safety Standards |
N/A UL CSA CE |
CE Marking |
N/A EMC Directives |
California Proposition 65 |
N/A
⚠ CA WARNING Cancer risk from exposure to Nickel. See www.P65Warnings.ca.gov Risk of reproductive harm from exposure to Di-n-hexyl phthalate (DnHP). See www.P65Warnings.ca.gov Risk of cancer and reproductive harm from exposure to Di(2-ethylhexyl phthalate (DEHP). See www.P65Warnings.ca.gov See "?" or copy/paste www.P65Warnings.ca.gov in your browser. |
Insulation Class |
N/A UL, CSA: Class A [105ºC (221ºF)] EN: Class E [120ºC (248ºF)] |
Insulation Resistance (Motor) |
N/A 100 MΩ or more when 500 VDC megger is applied between the windings and the frame after continuous operation under normal ambient temperature and humidity. |
Insulation Resistance (Driver) |
N/A 100 M Ω or more when 500 VDC megger is applied between the power supply terminal and heat radiation plate after continuous operation under normal ambient temperature and humidity. |
Dielectric Strength (Motor) |
N/A Sufficient to withstand 0.5 kVAC at 50Hz applied between the windings and the frame for 1 minute after continuous operation under normal ambient temperature and humidity. |
Dielectric Strength (Driver) |
N/A Sufficient to withstand 0.5 kVAC at 50Hz applied between the power supply terminal and the heat radiation plate for 1 minute after continuous operation under normal ambient temperature and humidity. |
Ambient Temperature Range |
N/A 0ºC ~ +50ºC (+32ºF ~ +122ºF) (nonfreezing) |
Ambient Humidity |
N/A 85% max. (noncondensing) |
Operating Atmosphere |
N/A No corrosive gases or dust. Cannot be used in radioactive area, magnetic field, vacuum or other special environment. |
Degree of Protection |
N/A [Motor] IP40 [Driver] IP00 |
Speed Control Method (Select one of the following) |
N/A Internal potentiometer External DC voltage External potentiometer (20kΩ, 1/4W) |
Number of Speed Settings |
N/A 2-speed operation is possible |
Multi-Speed Setting Method |
N/A
External speed potentiometer or external DC voltage: 0 to 5 VDC, 1 mA min VR1 |
Acceleration/Deceleration Time |
N/A
0.1 to 12.0 s (Factory setting: 0.1 s) VR2 |
Instantaneous Stop |
N/A Yes |
Multi-Axes Control |
N/A Yes |
Alarm Output |
N/A Yes |
I/O Functions |
N/A
Direct Input Method: C-MOS Negative Logic Input Point: 5 Points Initial Assignment: START/STOP, RUN/BRAKE, FWD/REV, M0, ALM-RST Direct Output Method: Transistor and open-collector output Point: 2 Points Initial Assignment: SPEED-OUT, ALM-B |
|
|
|
|
|
|
|
|
