As informações abaixo estão em inglês
Product Line |
- Oriental Motor® |
Motor Type |
- Closed Loop |
Frame Size |
- 1.65 in42 mm |
Motor Length |
- 3.9 in.99 mm |
Speed-Torque Characteristics |
-
 Speed - Torque Characteristics |
Holding Torque |
- 211 oz-in1.5 N·m |
Shaft/Gear Type |
- Taper Hobbed Gear |
Gear Ratio (X:1) |
- 30 :1 |
Backlash |
- 15 arc min (0.25°) |
Feedback Device (Motor) |
- Resolver |
Electromagnetic Brake |
- Not Equipped |
Shaft |
- Single |
Power Supply |
- 24/48 VDC |
Current |
- 1.4 A |
Resolution (Resolution Setting: 1000 P/R) |
- 0.012 °/Pulse |
Permissible Speed Range (r/min) |
- 0 ~ 60 |
Rotor Inertia |
- 0.32 oz-in²58x10-7 kg·m² |
RoHS Compliant |
- Yes |
Safety Standards |
- CE |
CE Marking |
- EMC Directives |
Components |
- ARD-K [Driver] ARM46AK-T30 [Motor] |
Maximum Input Pulse Frequency |
-
When the host controller is a line driver output: 500 kHz (When pulse duty is 50%) When the host controller is an open-collector output: 250 kHz (When pulse duty is 50%)* *When driver cable CC36D1-1 is used. |
Control Command |
- Pulse input |
Insulation Class |
- [Motor] Class B [130ºC (266ºF)] |
Insulation Resistance (Motor) |
-
100 MΩ or more when 500 VDC megger is applied between the following places: Case - Motor and sensor windings |
Dielectric Strength (Motor) |
-
Sufficient to withstand the following for 1 minute: Case - Motor and sensor windings 1.0 kVAC 50 Hz or 60 Hz |
Ambient Temperature (Motor) |
-
-10 ~ 50ºC (14 ~ 122º) (non-freezing) (when a heat sink of a capacity at least equivalent to an aluminum plate with a size of 3.94 x 3.94 in., 0.24 in. thick is installed.) |
Ambient Temperature (Driver) |
- 0 ~ 50ºC (32 ~ 122ºF) (non-freezing) |
Ambient Humidity |
- 85% or less (Non-Condensing) |
Operating Atmosphere |
- No corrosive gases, dust water or oil |
Degree of Protection |
-
[Motor] IP65 (excluding the mounting surface and connector) [Driver] IP20 |
Stop Position Accuracy |
- ±4 arc minutes (±0.067º) |
Shaft Runout |
- 0.05 mm (0.002 in.) T.I.R. |
Concentricity |
- 0.075 mm (0.003 in.) T.I.R. |
Perpendicularity |
- 0.075 mm (0.003 in.) T.I.R. |
Radial Load |
- 0 in. from Shaft End = 2.2 lb0.2 in. from Shaft End = 3.1 lb0.39 in. from Shaft End = 4.5 lb0.59 in. from Shaft End = 6.7 lb0 mm from Shaft End = 10 N5 mm from Shaft End = 14 N10 mm from Shaft End = 20 N15 mm from Shaft End = 30 N |
Axial Load |
- 3.3 lb15 N |
|
|
|
|
|
|
|
|
