Return Policy |
N/A This product cannot be cancelled or returned once the order has been processed. |
Motor Type |
N/A Closed Loop |
Frame Size |
N/A 1.1 in28 mm |
Motor Length |
N/A 2.78 in.70.5 mm |
Speed-Torque Characteristics |
N/A
 Speed - Torque Characteristics |
Holding Torque |
N/A 71 oz-in0.5 N·m |
Shaft/Gear Type |
N/A Taper Hobbed Gear |
Gear Ratio (X:1) |
N/A 30 :1 |
Backlash |
N/A 60 arc min (1°) |
Feedback Device (Motor) |
N/A Resolver |
Electromagnetic Brake |
N/A Not Equipped |
Shaft |
N/A Single |
Power Supply |
N/A 24 VDC |
Resolution (Resolution Setting: 1000 P/R) |
N/A 0.012 °/Pulse |
Permissible Speed Range (r/min) |
N/A 0 ~ 100 |
Rotor Inertia |
N/A 0.06 oz-in²11x10-7 kg·m² |
RoHS Compliant |
N/A Yes |
Safety Standards |
N/A CE |
CE Marking |
N/A EMC Directives |
California Proposition 65 |
N/A
⚠ CA WARNING Cancer risk from exposure to Nickel. See www.P65Warnings.ca.gov Risk of reproductive harm from exposure to Di-n-hexyl phthalate (DnHP). See www.P65Warnings.ca.gov Risk of cancer and reproductive harm from exposure to Di(2-ethylhexyl phthalate (DEHP). See www.P65Warnings.ca.gov See "?" or copy/paste www.P65Warnings.ca.gov in your browser. |
Components |
N/A ARD-KD [Driver] ARM24SAK-T30 [Motor] |
Insulation Class |
N/A [Motor] Class B [130ºC (266ºF)] |
Insulation Resistance (Motor) |
N/A
100 MΩ or more when 500 VDC megger is applied between the following places: Case - Motor and sensor windings |
Insulation Resistance (Driver) |
N/A
100 MΩ or more when 500 VDC megger is applied between the following places: FG terminal - Power input terminal |
Dielectric Strength (Motor) |
N/A
Sufficient to withstand the following for 1 minute: Case - Motor and sensor windings 1.0 kVAC 50 Hz or 60 Hz |
Dielectric Strength (Driver) |
N/A
No abnormailty is judged with the following application for 1 minute: FG terminal - Power input terminal 500 VAC at 50 Hz or 60 Hz |
Ambient Temperature (Motor) |
N/A
-10 ~ 50ºC (14 ~ 122º) (non-freezing) (when a heat sink of a capacity at least equivalent to an aluminum plate with a size of 3.94 x 3.94 in., 0.24 in. thick is installed.) |
Ambient Temperature (Driver) |
N/A 0 ~ 50ºC (32 ~ 122ºF) (non-freezing) |
Ambient Humidity |
N/A 85% or less (Non-condensing) |
Operating Atmosphere |
N/A No corrosive gases, dust water or oil |
Degree of Protection |
N/A
[Motor] IP20 [Driver] IP10 |
Stop Position Accuracy |
N/A ±4 arc minutes (±0.067º) |
Shaft Runout |
N/A 0.05 mm (0.002 in.) T.I.R. |
Concentricity |
N/A 0.075 mm (0.003 in.) T.I.R. |
Perpendicularity |
N/A 0.075 mm (0.003 in.) T.I.R. |
Radial Load |
N/A 0 in. from Shaft End = 3.3 lb0.2 in. from Shaft End = 3.8 lb0.39 in. from Shaft End = 4.5 lb0.59 in. from Shaft End = 5.1 lb0 mm from Shaft End = 15 N5 mm from Shaft End = 17 N10 mm from Shaft End = 20 N15 mm from Shaft End = 23 N |
Axial Load |
N/A 2.2 lb10 N |
Driver Type |
N/A Built-in Controller (Stored Data Type) |
Number of Positioning Data Sets |
N/A 64 Points |
Positioning Operation |
N/A One-Shot, Linked, Linked 2, Sequential, Direct, Pushing |
Protocol |
N/A Modbus Protocol (Modbus RTU mode) |
Electrical Characteristics |
N/A
EIA-485 compliance Twisted-pair wire (TIA/EIA-568B CAT5e or greater recommended) is used up to a total extension length of 50 m. |
Transmission/Reception Mode |
N/A Half-duplex communication |
Baud Rate |
N/A 9600 bps/19200 bps/57600 bps/115200 bps |
Physical Layer |
N/A Start-stop synchronization mode (data length: 8-bit, stop bit: 1-bit/2-bit, parity: none/odd/even) |
Connection Type |
N/A Up to 31 units can be connected to one programmable controller (master equipment). |
|
|
|
|
|
|
