Oriental Motor

ORIENTAL MOTOR U.S.A. Corp.
570 Alaska Avenue
Torrance, CA 90503
1-800-GO-VEXTA (468-3982)

Print Back
The BLE2 Series features a compact, high-power and high-efficiency brushless DC motor. The entire motor structure features our latest brushless DC motor technology and has been innovated in pursuit of the optimal performance. It is combined with a Driver that can be digitally set and controlled via external DC voltage or by the front panel.
  • Speed Control Range 80~4000 r/min
  • Torque Limit Function
  • The Driver can be Digitally Set and Controlled via the Front Panel.
*Connection Cable Required.

Unit of Measure

Specifications

Lead Time1 - {Contact your local sales office for more information.}

Motor Type

 - Brushless DC Motor

Motor Frame Size

 - 2.36 in.

Output Power

 - 30 W (1/25 HP)

Power Supply

 - Single-Phase 100-120 VAC

Shaft/Gear Type

 - Round Shaft with Flat (No Gearhead)

Output Shaft Diameter

 - 8 mm

Rated Torque

 - 0.85 lb-in

Electromagnetic Brake

 - Equipped

Variable Speed Range (r/min)

 - 80 ~ 4000

Permissible Load Inertia

 - 9.8 oz-in²

Permissible Radial Load

 - 0.39 in. from Shaft End = 18 lb0.79 in. from Shaft End = 22 lb

Permissible Axial Load

 - Half of motor mass max.

Max. Extension Length

 - 20.5 m (65.6 ft.)

Components

 - BLE2D30-AM, Brushless DC Motor Driver (Single-Phase 100-120 VAC) ($319.00)
BLM230HPM-ACS, 30 W (1/25 HP) Brushless DC Motor Round Shaft with Flat (No Gearhead) (:1 Gear Ratio) ($428.00)

RoHS Compliant

 - These products do not contain substances that exceed the regulation values in the RoHS Directive.

Safety Standards

 - UL CSA CE

CE Marking

 - Low Voltage Directives EMC Directives

Insulation Resistance (Motor)

 - 100 MΩ or more when 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity.

Insulation Resistance (Driver)

 - 100 MΩ or more when a 500 VDC megger is applied between the power supply terminal and the protective earth terminal and between the power supply terminal and the I/O signal terminal after continuous operation under normal ambient temperature and humidity.

Dielectric Strength (Motor)

 - Sufficient to withstand 1.5 kVAC at 50 Hz applied between the windings and the case for 1 minute after continuous operation under normal ambient temperature and humidity.

Dielectric Strength (Driver)

 - Sufficient to withstand 1.5 kVAC at 50 Hz applied between the power supply terminal and the protective earth terminal for 1 minute and 1.5 kVAC at 50 Hz between the power supply terminal and the I/O terminal for 1 minute after continuous operation under normal ambient temperature and humidity.

Temperature Rise (Motor)

 - Temperature rise of the heat sink is 90ºF (50ºC) or less measured by the thermocouple method after rated continuous operation under normal ambient temperature and humidity.

Temperature Rise (Driver)

 - Temperature rise of the heat sink is 90ºF (50ºC) or less measured by the thermocouple method after rated continuous operation under normal ambient temperature and humidity.

Ambient Temperature Range

 - Motor: 32ºF ~ 104ºF (0ºC ~ 40ºC), nonfreezing
Driver: 32ºF ~ 122ºF (0ºC ~ 50ºC)

Ambient Humidity

 - 85% or less, noncondensing

Altitude

 - Up to 3300 ft (1000 m) above sea level.

Operating Atmosphere

 - No corrosive gases or dust. Cannot be used in a radioactive area, magnetic field, vacuum or other special environment.

Thermal Class

 - CSA standards: 105 (A), EN standards: 120 (E) UL

Degree of Protection

 - Motor: IP66 (excluding installation surface)
Driver: IP20

Brake Specifications

Static Friction Torque

 - 13.6 oz-in

Brake Type

 - Power off activated type. Automatically controlled by the driver.

Continuous Regenerative Power

 - 70 W

Instantaneous Regenerative Power

 - 720 W

Driver Functions

Speed Control Method (Select one of the following)

 - Digital Setting:
  • Control Panel
  • Data Setting Software MEXE02

Analog Setting:
  • External Speed Potentiometer
  • External DC Voltage: DC 0 ~ 10 V, 1 mA min.

Number of Speed Settings

 - Max. 16 points (Factory setting: 4 points)

Acceleration/Deceleration Time

 - 0.0 ~ 15.0 s (Factory setting: 0.5 s)

Torque Limiting

 - 0~300% (Factory Setting: 300%)
Digital Setting:
  • Control Panel
  • Data Setting Software MEXE02
Analog Setting
  • External Speed Potentiometer
  • External DC Voltage: DC 0 ~ 10 V, 1 mA min.

Input Signals

 - Photocoupler Input Input Resistance: 6.6 kΩ
Connectable External DC Power Supply: 24 VDC -15 ~ +20% Current 100 mA min.
Sink Input/Source Input Supports External Wiring
Arbitrary signal assignment to IN0 ~ IN6 input (7 points) is possible. [ ]: Initial Setting
[FWD], [REV], [STOP-MODE], [M0], [M1], [ALARM-RESET], [MB-FREE], M2, M3, H-FREE, TL, INFO-CLR, HMI, EXT-ERROR, START/STOP, RUN/BRAKE, CW/CWW

Output Signals

 - Photocoupler and Open-Collector Output (ON Power supply: 1.6 V max.)
External Power Supply: 4.5 ~ 30 V 100 mA max. (5 mA min. for SPEED-OUT output)
Sink Output/Source Output Supported through external wiring
Arbitrary signal assignment to OUT0, OUT1 (2 points) is possible. [ ]: Initial setting
[SPEED-OUT], [ALARM-OUT], MOVE, INFO, TLC, VA, DIR

Protective Function

 - When the following protective functions are activated, the output from ALARM-OUT will turn OFF and the motor will perform a coasting stop. At the same time, the alarm code will be displayed and the Alarm LED flashes red.
Overcurrent, main circuit overheat, overvoltage, undervoltage, sensor error, main circuit output error, overload, over-speed, EEPROM error, initial sensor error, initial operation prohibited, external stop

Time Rating

 - Continuous

Speed-Torque


 

Dimensions


 

 

Product Number


 

System


 

  • 1 Quoted Ship Date for orders placed before 12:00 pm PST. Quantities may affect Shipping Date.