Return Policy |
N/A This product cannot be cancelled or returned once the order has been processed. |
Product Line |
N/A VEXTA® |
Motor Type |
N/A 5-Phase |
Frame Size |
N/A 1.1 in28 mm |
Motor Length |
N/A 1.26 in.32 mm |
Speed-Torque Characteristics |
N/A
 Speed - Torque Characteristics |
Holding Torque |
N/A 6.8 oz-in0.048 N·m |
Type |
N/A High-Torque |
Shaft/Gear Type |
N/A Round Shaft (No Gearhead) |
Electromagnetic Brake |
N/A Not Equipped |
Encoder |
N/A Not Equipped |
Shaft |
N/A Double |
Power Supply |
N/A 24 VDC |
Current |
N/A 0.7 A |
Basic Step Angle |
N/A 0.72º |
Rotor Inertia |
N/A 0.049 oz-in²9x10-7 kg·m² |
RoHS Compliant |
N/A Yes |
Safety Standards |
N/A CE |
CE Marking |
N/A EMC Directives |
California Proposition 65 |
N/A
⚠ CA WARNING Cancer risk from exposure to Nickel. See www.P65Warnings.ca.gov Risk of reproductive harm from exposure to Di-n-hexyl phthalate (DnHP). See www.P65Warnings.ca.gov Risk of cancer and reproductive harm from exposure to Di(2-ethylhexyl phthalate (DEHP). See www.P65Warnings.ca.gov See "?" or copy/paste www.P65Warnings.ca.gov in your browser. |
Insulation Resistance |
N/A [Motor] 100 MΩ or more when 500 VDC megger is applied between the windings and the case under normal ambient temperature and humidity. |
Dielectric Strength |
N/A [Motor] Sufficient to withstand 0.5 kVAC at 50 Hz or 60 Hz applied between the windings and the case for 1 minute under normal ambient temperature and humidity. |
Dielectric Strength (Driver) |
N/A [Driver] Sufficient to withstand the following for 1 minute under normal temperature and humidity: FG terminals – Power input terminal - 500 VAC, 50 or 60 Hz |
Insulation Class |
N/A [Motor] Class B [266ºF (130ºC)], Recognized as Class A 221ºF (105ºC) by UL standard |
Ambient Temperature Range |
N/A [Driver] 32ºF ~ 104ºF (0ºC ~ 40ºC) (nonfreezing) [Motor] 14ºF ~ 122ºF (-10ºC ~ 50ºC) (nonfreezing) |
Ambient Humidity |
N/A 85% or less (noncondensing) |
Operating Atmosphere |
N/A No corrosive gases, dust, water or oil. |
Temperature Rise |
N/A [Motor] Temperature rise of the coil measured by the Change Resistance Method is 144ºF (80ºC) or less (at rated current, at standstill, five phases energized). |
Shaft Runout |
N/A 0.002 in (0.05 mm) T.I.R. at top of output shaft |
Concentricity |
N/A 0.003 in. (0.075 mm) T.I.R. |
Perpendicularity |
N/A 0.003 in. (0.075 mm) T.I.R. |
Stop Position Accuracy |
N/A ±5 arc minutes (±0.084º) |
Radial Play |
N/A 0.001 inch (0.025 mm) max. of 1.12 lb. (5 N) |
Axial Play |
N/A 0.003 in (0.075 mm) max. of 2.2 lb. (10 N) |
Radial Load |
N/A 0 in. from Shaft End = 5.6 lb0.2 in. from Shaft End = 7.6 lb0.39 in. from Shaft End = 11.7 lb0 mm from Shaft End = 25 N5 mm from Shaft End = 34 N10 mm from Shaft End = 52 N |
Axial Load |
N/A 1.1 lb5 N |
Number of Positioning Data Sets |
N/A 63 Points |
Positioning Operation |
N/A Sequential Positioning, Data-Select Positioning |
Protocol |
N/A Modbus Protocol (Modbus RTU mode) |
Electrical Characteristics |
N/A
EIA-485 compliance Twisted-pair wire (TIA/EIA-568B CAT5e or greater recommended) is used up to a total extension length of 164 ft. (50 m). |
Transmission/Reception Mode |
N/A Half-duplex communication |
Baud Rate |
N/A 9600 bps/19200 bps/57600 bps/115200 bps |
Physical Layer |
N/A Start-stop synchronization mode (data length: 8-bit, stop bit: 1-bit/2-bit, parity: none/odd/even) |
Connection Type |
N/A Up to 31 axes can be connected to one Master Controller |
|
|
|
|
|
|
|
|
|
